How To Put A Window Pane Back In

Download Article

Bandy out your broken or cracked window for some brand-new glass

Download Commodity

You're sitting at dwelling house enjoying your day, when of a sudden, you hear a loud crash. The neighbor's baseball cracked one of your window panes! You might be worried that yous'll need a whole new window or pay an expert to set up the pane, merely don't panic withal. Replacing a window pane is a lot easier than y'all might think. You just demand the right tools and a few hours to accept care of information technology by yourself for a fraction of the price.

1. 1

   Lay a drop cloth or sheet under the window to avoid making a mess. Fixing a window pane can exist a messy chore, and you'll probably get dust, putty, and glass everywhere. Catch all of this droppings by setting up a drop cloth earlier you start working to protect your floors.^[1]

   • Y'all might want to put a drop cloth on the other side of the window too, simply to be safety.

2. 2

   Put on thick gloves and eye protection before starting. Any time y'all're working with glass, there's a adventure for breaking a piece and hurting yourself. Ever put on a pair of thick gloves to protect your hands, and also goggles or a face shield to protect your eyes.^[2]

   • If you're wearing goggles, make sure they wrap around your eyes to protect them from all sides.

   Advert

3. 3

   Pop off the glazing around the pane with a sharp putty knife. Window panes are held in past a putty called glazing, so you lot'll accept to remove this to get the pane out. Use a putty knife—the sharper the better. Observe the line separating the glaze from the wood at whatsoever point, and insert the putty knife there. Then push towards the pane to break the glazing off. Continue working your fashion around the pane and pop off all the glazing belongings it in.^[3]

   • If the glazing is tough to get off, try heating it up with a hairdryer or estrus gun. This can soften the glazing and make removing information technology easier.^[4]
   • You could also use a razor or utility knife to get the glazing off.

4. 4

   Scrape off whatever remaining glazing or glue along with border of the pane. When you break off all the big pieces of glazing, in that location might still be some remnants left over. Scrape your knife effectually the edge of the pane to go rid of whatsoever leftovers holding the pane in.^[5]

5. five

   Record an Ten on both sides of the pane with duct tape. To get the pane out completely, you'll take to intermission it. Forestall glass from flying everywhere by taping off the window first. Make an X across each side of the pane with duct tape then the glass stays together when you lot break information technology.^[6]

   • If the pane was already broken, then you might non accept to crack it more than. If you can get a grip on the pane, and then yous tin can just pull it out.
   • If yous're removing a pane in a loose window sash, the wooden part that holds the panes, then you can identify information technology on a workbench, cover the pane with a rag, and hit it with a hammer instead of taping it.^[seven]

6. 6

   Interruption the pane by borer it with a hammer or like tool. Apply either a hammer or the handle of a screwdriver and tap the pane until it breaks. Tap in a few different spots and so the pane breaks all over.^[8]

   • Y'all're just trying to crack the pane. You don't have to smack it hard to try and smash information technology.

7. 7

   Pop the old pane out of position and remove all the glass. In one case the pane is cleaved, it should come out easily. Take hold of information technology in any spot you can get a grip, and pull it out.^[9] Then check along the sash for any leftover drinking glass, and pull or scrape information technology out before moving on.^[10]

   • If there isn't a spot to take hold of the pane, then endeavour going to the other side of the window and pushing it out.
   • Fifty-fifty though you taped the glass, some shards might still break free as you remove the pane. Check the floor and pick up whatsoever loose pieces.
   • Some windows use hooks or other pocket-size metallic pieces to go along the panes in identify. If you see any of these, pull them out too.

8. 8

   Sand the border of the sash. Use coarse sandpaper and sand around the whole rabbet, or the groove where the window sits. Polish everything down to the bare wood.^[11]

   • Keep your gloves on while you lot're sanding. If you lot missed any glass pieces, you could get a serious cut.

Advertisement

1. one

   Become a replacement drinking glass pane with the same dimensions equally the old one. Y'all can become replacement glass panes at any hardware store. Measure out the length and height of the space, and use those dimensions to buy a new pane that fits into the sash.^[12]

   • Since forest expands, get out a bit of extra room to let for that. In general, subtracting ¹⁄_viii  in (0.32 cm) from your measurement leaves plenty room. Then if your sash space is 12 in (30 cm), get a pane that'due south xi 7/eight in (29.seven cm) for some extra room.
   • If y'all can't go a pane that fits into the sash, you could also become a larger piece of drinking glass and cut it to fit into position.
   • Hardware stores will too cut the pane for you lot if you bring your measurements in.

2. ii

   Run caulk around the border of the sash. Use your caulk gun and angle it onto the notch department of the sash. Clasp a dewdrop of caulking on all four sides of the sash. This is important to cushion the glass and weather-seal the window.^[thirteen]

   • Work quickly afterwards this so the caulk doesn't dry before you put the drinking glass in.
   • In full general, silicone or polymer caulk is recommended for windows. These are flexible enough to aggrandize with the window and make a weather-tight seal. Y'all could as well use butyl rubber.^[fourteen]

3. three

   Press the new pane into the caulk. Agree the new pane firmly and line it up with the sash. Slide information technology into the sash from the bottom first, then piece of work your way up until the pane is completely in. Printing down gently so the glass adheres to the caulk.^[fifteen]

   • Brand sure the pane is completely in the sash earlier letting go of information technology. If it's still loose, it could fall out and break.
   • Do your best to line upwardly the pane perfectly the kickoff time. Removing it to reset it will make a mess and could intermission the drinking glass.

4. 4

   Insert a glazer's point in the center of each side to secure the pane. A glazer's point is a piddling metal tab that helps keep the pane in place. Each one has a pointed end and a toothed finish. Accommodate each one so the pointed side points toward the wood. Then use your putty knife to press information technology into the woods at the heart of the pane. Put one of these on each side of the glass.^[xvi]

   • You can become glazer'due south points at hardware stores.
   • If the pane is 12 in (30 cm) or longer on any side, then put points every four–6 in (10–15 cm) instead.

5. 5

   Knead 4 pieces of putty into ³⁄₄  in (1.ix cm) thick strips. Window putty is difficult at first, so you need to warm it upwardly. Knead it between your hands to warm and soften it up. And then mold iv strips that are about ³⁄₄  in (1.9 cm) thick.^[17]

   • Putty normally comes in pre-made ropes. You tin get it from the hardware store.
   • Window putty or glazing also comes in a caulking tube. You might find this easier to work with. If yous apply information technology, employ information technology the same way you would employ caulk.^[eighteen]

6. vi

   Lay a strip of putty on each side of the pane. Press the putty firmly along the side of the pane and printing it into the forest to brand a tight seal. Do this on all iv sides so the window stays locked in identify.^[19]

   • Don't worry about keeping the putty neat. Y'all can make clean up the edges afterwards.

7. vii

   Smooth out the putty with your knife. Get-go at one of the corners of the window pane. Agree your putty knife at a 45-caste bending with the glass and tilt it to touch the wood on the window sash. Then press the blade down with your finger and pull the knife along that strip of putty to flatten it out. Peel off whatever excess putty that comes off. Repeat this on all four sides of the window.^[twenty]

   • If any putty gets on the drinking glass, scrape information technology off with your blade before it dries.
   • If you lot tin can see putty sticking out from either side of the window, and so in that location's a flake too much. Scrape this off every bit well then the window looks nice and corking.

8. 8

   Clean upward and let the putty dry for 7-10 days. Once all the putty is in place, all that'southward left to do is wait. Information technology takes 7-10 days for the putty to cure. In the meantime, clean up the mess and put your tools away while you lot wait for everything to set properly.^[21]

   • When you're picking up your drib cloth, fold it up carefully and comport it to a garbage can to dump out. Cheque carefully for any shards of glass that might accept fallen out while you were working.

9. 9

   Paint the window sash if you desire to. If you want some extra decoration or to encompass up whatsoever nicks you made while fixing the window pane, a few coats of paint volition practice the job. Outset by covering the putty with an oil-based primer. When that dries, y'all can utilize a coat or 2 of paint to requite yous window a fresh new look.^[22]

   • Don't try to pigment until the putty is completely dry.
   • Scrub the window when yous're done to get rid of any excess pigment.

Advertisement

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Things You lot'll Need

• Gloves
• Goggles
• Putty knife
• Hammer
• Duct record
• Sheet or drop cloth
• Caulk and caulk gun
• Putty
• Primer and paint (optional)

Video

Thanks for submitting a tip for review!

About This Article

Thanks to all authors for creating a folio that has been read 37,476 times.

Did this article help y'all?

Source: https://www.wikihow.com/Replace-a-Window-Pane

Posted by: tranwhempos60.blogspot.com

Share this post